- Flashprog - sourcearcade.org

[announce] flashprog v1.2 is ready!
by Nico Huber 20 Aug '24

20 Aug '24

Hi all, I'm happy to announce the flashprog v1.2 release. This one should be particularly interesting for developers: We have finally added the first bits for multi-i/o fast reads and QPI support. QPI works well with a new driver for programmers based on the FT4222H. Dual- and quad-i/o reads are also implemented for the Dediprog SF600 and its successors. Of the latter, the SF600Plus-G2 is fully tested. Other versions, using the same protocol, should work as well. Dual-i/o is enabled by default for these. With all four i/o lines connected, quad-i/o reads can be enabled with $ flashprog -p dediprog:iomode=quad (don't forget to also set the `spispeed` to go even faster) SF600 models that use older protocol versions should work as well but are untested. For those, `iomode=dual` is necessary for dual- i/o. Test reports are most welcome! See also the full release notes at [1]. The code is available in Git[2] (tag `v1.2') and as tarball[3]. After the release is before the release, and we are currently loo- king for testers of new chipset support: On the Intel side we have patches prepared for Snow Ridge, Meteor Lake, and Emmitsburg (PCH) (newer Xeon-SP systems) [4]. For AMD, everything up to and including Zen 4 is supported as long as the chipset is not too locked down. More testing here would be welcome, though, so we know what configurations vendors ship. Happy flashing, Nico [1] https://flashprog.org/wiki/Flashprog/v1.2 [2] https://github.com/SourceArcade/flashprog [3] https://flashprog.org/releases/flashprog-v1.2.tar.bz2 [4] https://review.sourcearcade.org/q/status:open+topic:moar_ichspi

1 0

Preparing for flashprog v1.2
by Nico Huber 18 Aug '24

18 Aug '24

Hi all, we're preparing for our next release v1.2 [1]. This one should be particularly interesting for developers: With multi i/o and QPI support, and the right programmer, external flashing can be a lot faster now. There's a new driver for FTDI FT4222H USB-to-SPI bridges -- probably our fastest supported programmer -- and Dediprog SF600 users benefit as well. Please grab the RC and test it :) As usual, the code is available through the tag `v1.2-rc1', and as tarball [2]. Cheers, Nico [1] https://flashprog.org/wiki/Flashprog/v1.2 [2] https://flashprog.org/releases/flashprog-v1.2-rc1.tar.bz2

1 0

Issue report - Error accessing ICH RCRB, 0x4000 bytes at 0x00000000fed1c000
by Paolo Giordanello 15 Aug '24

15 Aug '24

Hello, While I was trying to internally flash the bios chip I step in this issue. I am nowhere near a programmer or computer literate, but I followed step by step the documentation. Are you familiar with this issue? Many thanks for your work!! paolo@localhost:~> sudo '/usr/local/sbin/flashprog' -p internal -V [sudo] password di root: flashprog unknown on Linux 6.10.3-1-default (x86_64) flashprog is free software, get the source code at https://flashprog.org Using clock_gettime for delay loops (clk_id: 1, resolution: 1ns). flashprog was built with GCC 13.3.1 20240807 [revision 9d368828bd4d04ce507e02a581be850fca849fae], little endian Command line (3 args): /usr/local/sbin/flashprog -p internal -V Initializing internal programmer Found candidate at: 00000500-00000528 Found coreboot table at 0x00000500. Found candidate at: 00000000-00000900 Found coreboot table at 0x00000000. coreboot table found at 0x7f75b000. coreboot header(24) checksum: 4835 table(2280) checksum: 1d14 entries: 33 Vendor ID: LENOVO, part ID: ThinkPad T440p Using Internal DMI decoder. DMI string chassis-type: "Laptop" Laptop detected via DMI. DMI string system-manufacturer: "LENOVO" DMI string system-product-name: "ThinkPad T440p" DMI string system-version: "1.0" DMI string baseboard-manufacturer: "LENOVO" DMI string baseboard-product-name: "ThinkPad T440p" DMI string baseboard-version: "1.0" W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect. Active config mode, unknown reg 0x20 ID: 00. Found chipset "Intel QM87" with PCI ID 8086:8c4f. This chipset is marked as untested. If you are using an up-to-date version of flashprog *and* were (not) able to successfully update your firmware with it, then please email a report to flashprog(a)flashprog.org including a verbose (-V) log. Thank you! Enabling flash write... Root Complex Register Block address = 0xfed1c000 Error accessing ICH RCRB, 0x4000 bytes at 0x00000000fed1c000 /dev/mem mmap failed: Operation not permitted FAILED! FATAL ERROR! Error: Programmer initialization failed. paolo@localhost:~>

2 2

Fwd: Asrock B550M Pro4 -V and -VVV
by Nico Huber 24 May '24

24 May '24

Hi admkukuh, thanks for your report. It was stuck in the moderation queue because of the big images (not suited for a mailing list). Hence, I'm forwarding it without the images. It's amazing to see that the DOS port still works :) Did you also have to modify the stock BIOS to enable flashprog to read? Or was it only necessary to write? We could add a DEP (depends) entry to our list of known boards, I guess. Cheers, Nico -------- Forwarded Message -------- Subject: Asrock B550M Pro4 -V and -VVV Date: Wed, 22 May 2024 06:06:29 +0700 From: admkukuh <minecraftertamvan(a)gmail.com> To: flashprog(a)flashprog.org Below i attach success on B550 Chipset, i use B550M Pro4, but the stock bios needs to be modified, so i dump the bios chip that was flashed internally using asrock instant flash with the latest bios, dump it using programmer, remove AmdSpiRomProtectDXE from the bios, and Flashprog is able to read and write:[image: image.png] [image: image.png]

1 0

flashprog v1.1 -- our second feature release
by Nico Huber 03 May '24

03 May '24

Hi all, after a quiet week with the RC1, I'm happy to announce flashprog v1.1. This release brings a progress bar (--progress), support for Dediprog SF700 and SF600Plus-G2 programmers, and some more additions, fixes and tunings. You can find the full release notes on the wiki [1]. The code is available through the v1.1 tag and as a tarball [2]. Happy flashing, Nico [1] https://flashprog.org/wiki/Flashprog/v1.1 [2] https://flashprog.org/releases/flashprog-v1.1.tar.bz2

1 0

Preparing for new feature release with v1.1-rc1 | Please test!
by Nico Huber 27 Apr '24

27 Apr '24

Hi all, I'm glad to announce a new release candidate v1.1-rc1. 55 commits went into it, during a little more than four months. The most pro- minent changes are: * The `serprog' protocol now supports multiple CS lines. Which can be selected from the command line if the programmer supports it. * `serprog' driver now synchronizes more reliably after an aborted run and without the initial 1s delay. * We got rid of spurious attempts to memory map SPI flash chips by default. This was mostly visible with the `internal' programmer on AMD machines and `serprog' combined with big flash chips that just couldn't be mapped. * The CLI has a new `--progress' switch, finally(!) which makes it show progress bars for read/erase/write. Some programmer drivers were adapted to allow finer progress reporting. * The Dediprog SF600Plus-G2 (tested) and SF700 (untested) program- mers are supported now. And there were more, smaller changes and refactorings all over the place. As usual, the code is available through the tag `v1.1-rc1', and as tarball[1]. Please grab it! test it! Cheers, Nico [1] https://flashprog.org/releases/flashprog-v1.1-rc1.tar.bz2

1 0

Maintenance release v1.0.2-rc1
by Nico Huber 06 Apr '24

06 Apr '24

Hi, we found two regressions related to the Dediprog driver and large flash chips. There'll be a small maintenance release to fix them. The code of the release candidate is available through the tag `v1.0.2-rc1` and as a tarball[1]. Cheers, Nico [1] https://flashprog.org/releases/flashprog-v1.0.2-rc1.tar.bz2

1 1

[announce] Maintenance release v1.0.1 is ready
by Nico Huber 22 Jan '24

22 Jan '24

Hi, after a quiet test period, RC1 became the release. v1.0.1 fixes building our `linux_gpio_spi' driver with newer versions of libgpiod. Find more about it here: https://flashprog.org/wiki/Flashprog/v1.0.1 Cheers, Nico

1 0

Maintenance release v1.0.1-rc1
by Nico Huber 17 Jan '24

17 Jan '24

Hi all, flashprog has fallen behind with libgpiod compatibility. As it changed the API with version 2.0, which already ships with at least Fedora and ArchLinux. So we'll have a small maintenance release to include a new libgpiod bit-banging driver that uses the new API. The code is available through the tag `v1.0.1-rc1` and as a tarball[1]. As there are no other changes, only users of the linux_gpio_spi driver would have to test anything. Cheers, Nico [1] https://flashprog.org/releases/flashprog-v1.0.1-rc1.tar.bz2

1 0

Success with W25Q256JVEQ
by Mathieu Pilato 21 Dec '23

21 Dec '23

Hello, Please find enclosed the log describing the successful probe / read / flash / erase operations on a W25Q256JVEQ chip using the ch341a_spi programmer. Best regards,

2 2